Description of Template Manager Screen Tabs
Template Information Tab
Figure 3.21 Template Information tab
This tab contains general information about the template such as the Template Name, the Company Name, furnace information such as the furnace ID, the make and model of the furnace, the furnace dimensions, the temperature type (Fahrenheit or Celsius), the temperature range, the furnace type, the furnace use, the furnace class, and any Notes about the template. See “Description of Template Manager Screen Fields” for the maximum number of characters allowed per field.
Survey Information Tab
Figure 3.22 Survey Information tab
This tab contains information about the survey such as the Survey Duration in minutes, the Survey setpoint, The survey Tolerance, the Operator performing the survey, the simulated load, in pounds, and the Specification the survey meets.
Active TCs Tab
Figure 3.23 Active TCs Tab
This tab contains information about the active TCs such as the number of TCs used, the Gauge of the TC, the TC type, spool serial number, spool correction, and a check box for each of the TCs. There is also a check box to allow the user to use the active settings for the TCs or to individually select the TCs to use on the SDS instrument. Checking “Use these active TC settings” will set the checked TCs.
Controller Information Tab
Figure 3.24 Controller Information Tab
This tab contains information about the controllers such as the Controller Manufacturer, the Controller Model, and the instrument type. It also contains information about the PID settings such as the Cycle Time, the Dead Band, the Output Limit, the PB (gain), the Rate, and the Reset.
Description of Template Manager Screen Fields
This section will describe the Template Manager screen fields and list any constraint for the fields.
| Field Name | Description |
Maxiumum # of Characters
|
|
Template Name |
The name of the template | 22 |
|
Company Name |
The company's name |
40 |
|
Furnace ID |
The ID of the furnace |
17 |
|
Furnace Make/Model |
The make/model of the furnace |
22 |
|
Furnace Dimensions |
The height, length, and width of the furnace |
15 |
|
Temp Type |
The type of temperature (Fahrenheit or Celsius) |
1 (F or C) |
|
Temperature Range |
The low and high range of the furnace |
10 |
|
Furnace Type |
The type of furnace being surveyed |
20 |
|
Furnace Use |
What the furnace is used for |
15 |
|
Furnace Class |
The class of the furnace (V 1.101.0.80 and above) |
1 |
|
Notes |
Any additional notes desired |
63 |
|
Sample Interval |
The sample rate for the survey (V 1.101.0.71 and below only) |
N/A |
|
Survey Duration |
The duration of the survey in minutes |
3 |
|
Survey Tolerance |
The survey tolerance/uniformity required |
2 |
|
Simulated Load |
The simulated load in lbs |
5 |
|
Setpoint |
The survey setpoint |
4 |
|
Operator |
The operator performing the survey |
20 |
|
Specification |
The specification the survey meets |
25 |
|
Number of TCs |
The total # of TCs |
2 |
|
TC Type |
The type of TC |
3 |
|
TC Spool SN |
The spool number |
18 |
|
TC Spool Correction |
The spool correction factor |
8 |
|
TC Gauge |
The gauge of the TCs |
2 |
|
Use Active TC Settings |
Use the active TC Settings Option |
N/A |
|
Check box 1 - Check Box 40 |
The active TCs for the survey |
N/A |
|
SDS 8020 |
SDS 8020 instrument option (V 1.101.0.76 & below) |
N/A |
|
SDS 8040 |
SDS 8040 instrument option (V 1.101.0.76 & below) |
N/A |
|
Controller MFG |
The controller manufacturer |
18 |
|
Controller Model |
The controller make/model |
18 |
|
Instrument Type |
The type of the instrument |
1 |
|
Cycle Time |
The PID cycle time |
2 |
|
Dead Band |
The PID dead band |
4 |
|
Output limit |
The PID output limit |
3 |
|
PB (Gain) |
The PID PB (gain) |
5 |
|
Rate |
The PID rate |
6 |
|
Reset |
The PID reset |
6 |