Appendix 1: Factory Default Values for HP15-VR

	OXYGEN	CARBON	DEW POINT	MILLIVOLTS
Loop 1 Set Point:	0.0	0.00	0	0
Temperature Set Point:	0	0	0	0
Remote Set Point Setup:	None	None	None	None
Hysteresis:	0	0	0	0
Set Point:	0	0.0%	0	0

Set Points

Temperature Mode

Temperature Mode:

Fahrenheit

CO Factor

CO Factor:

N/A

200

N/A

H2 Factor

H2 Factor:

N/A

400

N/A

Pump Control

Current State:	Off	Off	Off	Off
Low Temp. Pump Cutoff:	Off	Off	Off	Off

Auto / Manual

Loop 1 Output:	Automatic	Automatic	Automatic	Automatic
Loop 2 Output:	Automatic	Automatic	Automatic	Automatic

PVT Type:

Oxygen

Carbon

Dew Point

Millivolts

Config Menu

IP Address:	192.168.0.200	192.168.0.200	192.168.0.200	192.168.0.200
Netmask:	255.255.255.0	255.255.255.0	255.255.255.0	255.255.255.0
Gateway:	192.168.1.1	192.168.1.1	192.168.1.1	192.168.1.1

Network Settings:

Loop 1 PID Settings:

Proportional Band:	20.0	20.0	20.0	20.0
Reset:	0.10	0.10	0.10	0.10
Rate:	0.00	0.00	0.00	0.00
Cycle Time:	16	16	16	16
Integral Preset:	0	0	0	0
Control Low Limit:	0	-100	-100	-100
Control High Limit:	100	100	100	100
Loop Mode:	Single Reverse	Dual Reverse	Dual Direct	Dual Reverse
Auto PID:	No	No	No	No
Switch Pt. PID 1 -> 2	999.9	99.99	9999	9999
Switch Pt. PID 2 -> 3	999.9	99.99	9999	9999
SP Lower Limit	-999.9	-99.99	-9999	-9999
SP Upper Limit	2999.9	299.99	29999	29999

Hi Limit Shuts Down Control:

	Input 1:	No	No	No	No
	Input 2:	No	No	No	No
	Input 3:	No	No	No	No
Zero Set Point Shuts Down Control:		No	Yes	No	Yes
Set Point Change Limit:		Off	Off	Off	Off

Config Menu (Continued)

	OXYGEN	CARBON	DEW POINT	MILLIVOLTS
Proportional Band:	4.4	4.4	4.4	4.4
Reset:	0.12	0.12	0.12	0.12
Rate:	2.16	2.16	2.16	2.16
Cycle Time:	16	16	16	16
Integral Preset:	0	0	0	0
Control Low Limit:	0	0	0	0
Control High Limit:	100	100	100	100
Loop Mode:	Single Reverse	Single Reverse	Single Reverse	Single Reverse
Auto PID:	No	No	No	No
Switch Pt. PID 1 -> 2	9999	9999	9999	9999
Switch Pt. PID 2 -> 3	9999	9999	9999	9999
SP Lower Limit	-9999	-9999	-9999	-9999
SP Upper Limit	29999	29999	29999	29999

Network Settings:(Continued) Loop 2 PID Settings:

	Input 1:	No	No	No	No
	Input 2:	Yes	Yes	Yes	Yes
	Input 3:	No	No	No	No
Zero Set Point Shuts Down Control:		No	No	No	No
Set Point Change Limit:		Off	Off	Off	Off

Hi Limit Shuts Down Control:

Burnoff Time (sec):	90	90	90	90
Recovery Wait Time (sec):	120	120	120	120
Interval:	720	720	720	720
Minimum mV:	800	800	800	800
Maximum Temperature:	2000	2000	2000	2000

Burn Off Setup:

Analog Input Setup:

Input Type:	2.5 Volts	2.5 Volts	2.5 Volts	2.5 Volts
Filter:	2	2	2	2
Initial Scale:	0	0	0	0
Full Scale:	2500	2500	2500	2500
Decimal Point Location:	0	0	0	0
Open Input Detection:	One Trip Point	Up Scale	Up Scale	Up Scale
Trip 1 Direction:	Input Above Set Point	Input Above Set Point	Input Above Set Point	Input Above Set Point
Trip 2 Direction:	Input Above Set Point	Input Above Set Point	Input Above Set Point	Input Above Set Point
Offset:	0	0	0	0
Trip Point 1 Set Point:	1400	0	0	0
Trip Point 1 Force Value:	0	0	0	0
Trip Point 2 Set Point:	0	0	0	0
Trip Point 2 Force Value:	0	0	0	0
Hi Input Limit SP	0	9999	9999	9999
Hi Input Limit Hysteresis	0	1	1	1

Analog Input 1 Settings:

Analog Input 2 Settings:

Input Type:

Type B

Type S

Filter:

Initial Scale:

Full Scale:

10000

Decimal Point Location:

Open Input Detection:

Down Scale

Up Scale

Trip 1 Direction:

Input Above Set Point

Trip 2 Direction:

Input Above Set Point

Offset:

Trip Point 1 Set Point:

Trip Point 1 Force Value:

Trip Point 2 Set Point:

Trip Point 2 Force Value:
0	0	0	0

Hi Input Limit SP

1800

Hi Input Limit Hysteresis

Config Menu (Continued)

	OXYGEN	CARBON	DEW POINT	MILLIVOLTS
Input Type:	Type S	Type S	Type S	Type S
Filter:	2	2	2	2
Initial Scale:	0	0	0	0
Full Scale:	10000	10000	10000	10000
Decimal Point Location:	0	0	0	0
Open Input Detection:	Up Scale	Up Scale	Up Scale	Up Scale
Trip 1 Direction:	Above Set Point	Above Set Point	Above Set Point	Above Set Point
Trip 1 Direction:	Above Set Point	Above Set Point	Above Set Point	Above Set Point
Offset:	0	0	0	0
Trip Point 1 Set Point:	0	0	0	0
Trip Point 1 Force Value:	0	0	0	0
Trip Point 2 Set Point:	0	0	0	0
Trip Point 2 Force Value:	0	0	0	0
Hi Input Limit SP	0	9999	9999	9999
Hi Input Limit Hysteresis	0	1	1	1

Analog Input Setup: (Continued) Analog Input 3 Settings:

Analog Output Setup:

Analog Output 1 Assignment:	PV1 Retrans	PV1 Retrans	PV1 Retrans	PV1 Retrans
Exponent:	0	0	0	0
Full Scale:	2000	2000	2000	2000
Range	209	200	200	200
Offset:	0	0	0	0
O2 Exponent Range	0	0	0	0
Current Selection	4-20mA	4-20mA	4-20mA	4-20mA

Analog Output 1 Settings:

Analog Output 2 Assignment:	Loop 2 Inc.	Loop 2 Inc.	Loop 2 Inc.	Loop 2 Inc.
Exponent:	0	0	0	0
Full Scale:	2000	2000	2000	2000
Range	3000	2000	2000	2000
Offset:	0	0	0	0
O2 Exponent Range	0	0	0	0
Current Selection	4-20mA	4-20mA	4-20mA	4-20mA

Analog Output 2 Settings:

Alarms:

Alarm Source:

Input 2

Alarm Action:

Process High

Alarm Set Point:

1800

Smart Alarm:

Disabled

0 SP Blocks Alarm:

Hysteresis:

On Delay Time:

Polarity

Normally Open

Alarm 1 Settings:

Alarm Source:	Input 2	Input 2	Input 2	Input 2
Alarm Action:	Process High	Process High	Process High	Process High
Alarm Set Point:	2000	2000	2000	2000
Smart Alarm:	Disabled	Disabled	Disabled	Disabled
0 SP Blocks Alarm:	No	No	No	No
Hysteresis:	1	1	1	1
On Delay Time:	0	0	0	0
Polarity	Normally Open	Normally Open	Normally Open	Normally Open

Alarm 2 Settings:

Alarm 3 Settings:

Alarm Source:	PV1	PV2	PV2	PV2
Alarm Action:	Process Low	Process High	Process High	Process High
Alarm Set Point:	1.0	2000	2000	2000
Smart Alarm:	Disabled	Disabled	Disabled	Disabled
0 SP Blocks Alarm:	No	No	No	No
Hysteresis:	1	1	1	1
On Delay Time:	0	0	0	0
Polarity	Normally Open	Normally Open	Normally Open	Normally Open