Client Instrument Setup

 

 

** All devices on the same Client port must utilize the same protocol

** An address of zero (0) will disable the instrument** Some controllers (AC20 for example) can provide dual functions (atmosphere and events) and must have the same address assigned for both.

 

This screen will allow the user to configure up to eighteen (18) Client instruments through the 9205 controller (7 are reserved). 

 

Clicking on the “Value” field for any instrument will allow the user to select the Client instrument.

 

Instrument

This value will allow the user to select the Client instrument type.

 

List of Instruments

The following is the list of instruments available as Client instruments:

 

SSi AC20

[A]Yokogawa 750

[A]Honeywell UDC3300

[A]Dualpro LP1 Modbus

[A]Dualpro LP2 Modbus

[A]Dualpro LP1 MMI

[A]Dualpro LP2 MMI

[A]Eurotherm 2404

[A]Eurotherm 2500

[A]CarbPro v3.5

[A]CarbPro v3.0

CarbPC

[A]9200 LP1

IR Base

MGA

Honeywell UDC3200

SSi 7EK

[T]Yokogawa 750

[T]Honeywell UDC3300

[T]Dualpro LP1 Modbus

[T]Dualpro LP2 Modbus

[T]Dualpro LP1 MMI

[T]Dualpro LP2 MMI

[T]Eurotherm 2404

[T]Eurotherm 2500

Unipro v3.5

Unipro v3.0

[T]Carbpro v3.5 Client

[T]Carbpro v3.0 Client

10Pro

Dualpro IN C

[T]9200 LP1

[T]9200 LP2

[T]9200 LP3

9100 LP2

Eurotherm 2704 LP1

Eurotherm 2704 LP2

Eurotherm 2704 LP3

VC Base 1

VC Base 2

VC Base 3

VC Base 4

AIPC

SSi 7SL

SSi eFlo

UMC800 LP1

SSi Quad AO1

SSi Quad AO2

SSi Quad AO3

SSi Quad AO4

Yokogawa UT350

Yokogawa 750 Lp 2

Yokogawa UP350

Honeywell DCP551

Ascon 08

SSi X5

SSi M4L

SSi X5/Timer

SSi SPUD

SSi AIB3

SSi H2 Cell

Flow Meter Short

SSi O2 Remote

SSi Dual Motor Board

SSi Smart AIB 3

O2 Block

Waukee Valvetronic+

SSi eSPP

EL-Flow

SSi AC E

Yokogawa 750E

Mod Mux

Dualpro E Modbus

Dualpro E MMI

Carbpro E v3.5

Carbpro E v3.0

Eurotherm 2500

SSi 8-8

SSi 9200 E

Micrologix PLC

MCM Module

PLC DF1

SLC DF1

User 1

User 2

User 3

User 4

User 5

User 6

User 7

User 8

User 9

User 10

User 11

User 12

User 13

User 14

User 15

User 16

 

Some instruments may not be shown in the list of instruments. User Instruments 1 through 16 are used to set up a non-listed instrument as a Client instrument using the

menu.

 

Address

This value allows the user to select the address that corresponds with the controller selected, with a range of 0 to 249.

 

Port

The options for this field are: Client 1, Client 2, RS-232, IP Address 1, IP Address 2, IP Address 3, IP Address 4, Passive, or Client 3/RS-232.

Client 1 – terminals 5(-), 6(+)

Client 2 – terminals 22(+), 23(-)

RS-232