Communications Setup

Communications Setup
Warning: Changes to this screen should not be made without consulting SSi at 513-772-0060.

This screen will show the Ethernet and RS-232/RS-485 communications information for the 9130 controller.

 

IP Address

NOTE:  This screen option is for changing the controller's IP address.  If you need to change the IP address of the Touch Screen, see the instructions in Appendix A of the Touch Screen Manager manual, available at www.supersystems.com.

 

This will identify the IP address of the controller.  Please consult your Systems Administrator before changing this value as it can affect communications to the 9220 controller or to other devices on your network.  This is necessary if the Touchscreen will be communicating to the 9220 over Ethernet communications.  The IP address must be in the “xxx.xxx.xxx.xxx” format.

 

IP Mask

NOTE:  This screen option is for changing the controller's IP mask.  If you need to change the IP mask of the Touch Screen, see the instructions in Appendix A of the Touch Screen Manager manual, available at www.supersystems.com.

 

This will identify the Subnet mask of the controller.  The Subnet mask must be in the “xxx.xxx.xxx.xxx” format.

 

IP Gateway

NOTE:  This screen option is for changing the controller's IP gateway.  If you need to change the IP gateway of the Touch Screen, see the instructions in Appendix A of the Touch Screen Manager manual, available at www.supersystems.com.

 

This will identify the IP gateway of the controller.  The IP gateway must be in the “xxx.xxx.xxx.xxx” format.

 

RS-232B Baud

This will set the baud rate for RS-232 communications.  This is necessary if the Touchscreen will be communicating through the Com ports.  The list of options is:

1200        14400        57600

2400        19200        76800

4800        28800        115200

9600        38400

 

RS-232B Mode

This will set the mode for RS-232 communications.  This is necessary if the Touchscreen will be communicating through the Com ports.  The list of options is:

Modbus

Cal Term

Modbus/DF1 Master

 

Host 485 Baud

This will set the baud rate for RS-485 communications.  This is necessary if the Touchscreen will be communicating through the Com ports.  The list of options is:

1200        14400        57600

2400        19200        76800

4800        28800        115200

9600        38400

 

Host 485 Mode

This will set the mode for RS-485 communications.  This is necessary if the Touchscreen will be communicating through the Com ports.  This setting is fixed at Modbus.

 

Host 485 Address

This will set the address for RS-485 communications.  This is necessary if the Touchscreen will be communicating through the Com ports.  The range is 1 – 247.

 

Client 1 Baud

This will set the baud rate for Client 1 communications.  The list of options is:

1200        14400        57600

2400        19200        76800

4800        28800        115200

9600        38400

 

Client 1 Mode

This will set the mode for Client 1 communications.  This list of options is:

MMI

Modbus Master

Yokogawa

Modbus Host

 

Client 2 Baud

This will set the baud rate for Client 2 communications.  The list of options is:

1200        14400        57600

2400        19200        76800

4800        28800        115200

9600        38400

 

Client 2 Mode

This will set the mode for Client 2 communications.  This list of options is:

MMI

Modbus

ADAM

SSi Analog Input Board

Yokogawa

 

RS-232A Baud

This will set the baud rate for RS-232 communications.  This is necessary if the Touchscreen will be communicating through the Com ports.  The list of options is:

1200        14400        57600

2400        19200        76800

4800        28800        115200

9600        38400

 

RS-232A Mode

This will set the mode rate for RS-232 communications.  This is necessary if the Touchscreen will be communicating through the Com ports.  This list of options is:

Cal Term

Modbus

 

The Return button will return the user to the menu screen.